Alarm.com Indoor Wireless IP Fixed Camera with Night Vision (ADC-V522IR)
Features
HD 1080p video
IR night vision
Wide dynamic range (WDR)
Two-Way Audio (see Two-Way Audio Compatibility FAQ)
Included accessories
Wi-Fi Video camera
Camera stand
Quick Installation Guide
Mounting hardware
Power adapter (10 feet)
Alarm.com Indoor Wireless IP Fixed Camera with Night Vision (ADC-V522IR)
$109.00
Out of stock
Out of stock
Description
Features
- HD 1080p video
- IR night vision
- Wide dynamicÿrange (WDR)
- Two-Way Audio (seeÿTwo-Way Audio Compatibility FAQ)
Included accessories
- Wi-Fi Video camera
- Camera stand
- Quick Installation Guide
- Mounting hardware
- Power adapter (10 feet)
Specifications
| Maximum resolution | 1920×1080 |
|---|---|
| Recording compression | H.264, MPEG-4 |
| Image sensor | 1/2.9″ CMOS, 2.12 MP, 1920×1080 |
| Lens | 2.8 mm, F1.85 |
| Angle of view | 113ø |
| Low-light sensitivity | 0 lux with IR |
| IR range | Up to 5ÿmeters (~15 feet) |
| Image adjustments | Flip, brightness, contrast, saturation, sharpness |
| Video motion detection | 3 windows, adjustable sensitivity and threshold |
| Wireless connectivity | 802.11 b/g/n/ac, 2.4 & 5 GHz |
| Ethernet connection | 10/100Mbps RJ-45 |
| Simultaneous viewers | 10 |
| Operating temperature | 0øC ? 40øC (32øF ? 104øF) |
| Operating humidity | 20%-80% (non-condensing) RH |
| Max power consumption | 12 V DC, 5 W |
| Dimensions (WxH) | 2.75? x 2.06? x 3.67? |
| Two-Way Audio compatibility | Hardware Version 0101ÿand Firmware Version IP8168-ALAM-0100b9 + |
For Internet service andÿbandwidth requirements, seeÿWhat are the internet service and bandwidth requirements for Alarm.com video devices?.
For information about frame rate (FPS), seeÿWhat is the frame rate for video?.ÿ
LED Guide
| LED pattern | Status | Description |
|---|---|---|
 |
Connected to internet | Local network and internet connection with Alarm.com IP.ÿ |
 |
Local network connection | Local network connection with local IP address, no internet.ÿ
Note: If the LED does not go to a solid green after a few minutes, seeÿCamera LED is blinking green.ÿ |
 |
Power on, or no network connection | Power on, system booting up typically 60-90 seconds.
If solid red for longer than 60-90 seconds, then there is noÿlocal or Internet connection. |
 |
Camera powering on, or firmware update | Camera is powering on, or a firmware update is in progress.ÿ |
 |
WPS mode | WPS mode is active. To enter WPS mode, press andÿhold the WPSÿbutton for about three seconds.ÿ |
 |
AP mode | Wi-Fi access point (AP) mode is active. To enter AP mode, press and hold the WPS button for about six seconds.ÿ |
 |
Factory reset | The camera is restoring to factory default settings.ÿ
Caution: If the camera is already installed, itÿmay need to be removed from the Alarm.com account and re-added after a factory reset.ÿ To perform a factory reset, press and hold the reset button for about 10-15 seconds.ÿ |
Note: The WPS and reset options share the same button on the ADC-522IR.ÿ
Additional information
| Weight | 10 oz |
|---|---|
| Dimensions | 5 × 5 × 5 in |
